LEVEL CONTROL INACTIVE = P1 = ? ( see QSilver7 reference #10) Refer to page 117 of the attached pdfĭOOR OPEN = P2 = a door is open this message appears after a defined road speed has been exceeded ( 1) ( see QSilver7 reference #10)ĮNGINE FAILSAFE PROG = P2 = a malfunction in the electronic engine-management system, which then reverts to an emergency default program allowing continued operation at reduced power and lower engine speeds ( 1)ĮXTERNAL TEMPERATURE 3.5 ☌ = external temperature warning at +3.0 ☌ but if its lower, it'll tell you what the exact temp ( 1)ĮXTERNAL TEMPERATURE 37 ☏ = external temperature warning at +27.0 ☏ but if its lower, it'll tell you what the exact temp ( 1)įAILSAFE PROG ACTIVE = apparently when the engine enters Limp Mode ( 1)įASTEN SEATBELTS = P2 = seat belts unbuckled, an indicator lamp with the safety belt icon also appears and an acoustic signal is sounded ( 1)įASTEN SEAT BELTS = P2 = person detected sans seat belts buckled ( see QSilver7 reference #10)įLAT TIRE = P1 = tire pressure is too low ( see QSilver7 reference #10) Stop the vehicle and switch off the engine immediately.
Refer to page 124 to page 132 of the attached pdfĬHECK TIRE PRESSURE = P2 = tire pressure is too low or high ( see QSilver7 reference #10)ĬOOLANT TEMPERATURE = P1 = The coolant is overheated. Refer to page 124 to page 132 of the attached pdfĬHECK SIDE LIGHTS = P2 = Defective bulb or circuit. CHECK LOWBEAMS = P2 = ( see QSilver7 reference #10)ĬHECK REAR LIGHTS = P2 = Defective bulb or circuit.
BMW DASHLIGHTS PDF
Refer to page 124 to page 132 of the attached pdf Refer to page 124 to page 132 of the attached pdfĬHECK LOWBEAM LIGHTS = P2 = Defective bulb or circuit. Refer to page 124 to page 132 of the attached pdfĬHECK LICPLATE LIGHT = P2 = Defective bulb or circuit. Refer to page 124 to page 132 of the attached pdfĬHECK HIGHBEAM LIGHT = P2 = Defective bulb or circuit. Refer to page 21 of the attached pdfĬHECK FRONT FOGLAMPS = P2 = Defective bulb or circuit. Refer to pages 126 and 132 of the attached pdfĬHECK BRAKE LININGS = P2 = Brake wear sensor open circuit refer to page 108 of the attached pdfĬHECK CONTROL OK = message that appears upon pressing the right cluster button with no errors found ( 1)ĬHECK COOLANT LEVEL = P2 = coolant level is too low refer to page 118 of the attached pdfĬHECK ENGINE OIL = P2 = oil level is at a minimum ( see QSilver7 reference #10)ĬHECK ENGINE OIL LEVEL = P2 = oil level is at the absolute minimum refer to page 115 of the attached pdfĬHECK FILLER CAP = P2 = Check to see whether the fuel filler cap has been properly closed. Refer to page 118 of the attached pdfĬHECK BRAKE LIGHTS = P2 = A lamp has failed or the electrical circuit has a fault. Refer to page 124 to page 132 of the attached pdfĬHECK BRAKE FLUID = P1 = fluid level has dropped nearly to the minimum. BRAKE LAMP CIRCUIT = P2 = ( see QSilver7 reference #10)ĬHECK BACK UP LIGHTS = P2 = Defective bulb or circuit. Here's a first pass (potential updates can be to " explain" each, & to separate into high/low cluster messages & priority 1/2 messages):īMW ASSIST INACTIVE = reputedly a message from the BMW Phone system wired to the SOS system ( 1) So, since that's in another forum and that thread is also apparently dead, we can improve upon that initial attempt by bringing over that information here and improving upon it.
BMW DASHLIGHTS SERIES
Googling, I found this similar attempt with a series of partial listings & descriptions: Looking up that message, I realized we might not have (yet) a definitive list of all possible BMW E39 instrument cluster messages to search from.
My cluster lost some of its pixels,i am getting a "stop-sec" does anyone what is missingĮDIT: As per JimLev, this message may be for the stopwatch but the goal of a comprehensive list of CLUSTER messages is still valid no matter what this particular message turns out to be. What got me thinking about this was the question today about (what might or might not be) a pixelated cluster message: People with pixelated messages often ask "what is this message" It's nice to know and add (eventually) to the BMW E39 technical glossary ( 1)Ģ. This is an attempt at compiling a comprehensive list of all BMW E39 high instrument cluster 20-character alphanumeric display messages.ġ. List of all possible BMW E39 instrument cluster text warnings & text messagesĮDIT: Clarified MID confusion as per JimLev.ĮDIT: Added TRANS FAILSAFE PROG (& description) as per Fudman.ĮDIT: Clarified this is the high cluster alphanumeric display as per QSilver7.ĮDIT: Added all known descriptions mostly based on this post and this pdf.
0 kommentar(er)
